Test
Trim Molding - 304 Stainless Random Swirl Finish
Trim Molding - 304 Stainless Random Swirl Finish
Cost Calculator >>
Order Samples >>
Description
These 304 stainless steel Random Swirl finish trim moldings are made from the same 24 gauge 304 stainless steel that we sell in sheet form. They are used to attach sheets as wall coverings and backsplashes, along with providing aesthetic covering for seams between sheets and around corners. Our trim moldings have deep pockets to allow for variance in the existing wall and also have extra wide nailing strips to make installation more convenient.
These 304 stainless steel Random Swirl finish trim moldings are made from the same 24 gauge 304 stainless steel that we sell in sheet form. They are used to attach sheets as wall coverings and backsplashes, along with providing aesthetic covering for seams between sheets and around corners. Our trim moldings have deep pockets to allow for variance in the existing wall and also have extra wide nailing strips to make installation more convenient.
Edge
The edge trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Edge trim molding is used to make a finished edge. The pocket is 1", and you do not need to subtract any for this specific trim molding.
Divide
The divide trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Divide trim molding is used to join two adjacent sheets on the same wall. The pocket for each side is 7/16", and subtracting 1/8" from each sheet will accommodate for this trim.
Inside Corner
The inside corner trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Inside corner trim molding is used to join two sheets at 90 degrees on an inside corner. The pocket for each side is 3/4", and subtracting 7/8" from the sheet size will accommodate for this trim.
Outside Corner
The outside corner trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Outside corner trim molding is used to join two sheets at 90 degrees on an outside corner. The pocket for each side is 3/4", and subtracting 3/16" from the sheet size will accommodate for this trim.
Note:
-When ordering material, you will need to subtract from the sheet size to account for the trim (see drawings).
-Trim molding can be attached to the wall with screws, nails, or adhesive prior to installing the sheets. + Read Description
Edge
The edge trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Edge trim molding is used to make a finished edge. The pocket is 1", and you do not need to subtract any for this specific trim molding.
Divide
The divide trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Divide trim molding is used to join two adjacent sheets on the same wall. The pocket for each side is 7/16", and subtracting 1/8" from each sheet will accommodate for this trim.
Inside Corner
The inside corner trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Inside corner trim molding is used to join two sheets at 90 degrees on an inside corner. The pocket for each side is 3/4", and subtracting 7/8" from the sheet size will accommodate for this trim.
Outside Corner
The outside corner trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Outside corner trim molding is used to join two sheets at 90 degrees on an outside corner. The pocket for each side is 3/4", and subtracting 3/16" from the sheet size will accommodate for this trim.
Note:
-When ordering material, you will need to subtract from the sheet size to account for the trim (see drawings).
-Trim molding can be attached to the wall with screws, nails, or adhesive prior to installing the sheets.
Edge
Description:
The edge trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Edge trim molding is used to make a finished edge. The pocket is 1”, and you do not need to subtract any for this specific trim molding.
Divide
Description:
The divide trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Divide trim molding is used to join two adjacent sheets on the same wall. The pocket for each side is 7/16”, and subtracting 1/8” from each sheet will accommodate for this trim.
Inside Corner
Description:
The inside corner trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Inside corner trim molding is used to join two sheets at 90° on an inside corner. The pocket for each side is ¾”, and subtracting 7/8” from the sheet size will accommodate for this trim.
Outside Corner
Description:
The outside corner trim molding is made from our 24 gauge 304 stainless steel random swirl sheet stock. Outside corner trim molding is used to join two sheets at 90° on an outside corner. The pocket for each side is ¾”, and subtracting 3/16” from the sheet size will accommodate for this trim.
Quick Request
Need something different?
Can't find what you're looking for?
Click here to submit your request.
<< Back
|
|
|
|
©2025 Stainless Supply. All Rights Reserved.
