1/4 Hard Copper sheet is pure copper that is slightly less malleable but much stronger than soft temper copper. This is very commonly used in roofing, trim, gutters, flashing, wiring, chimney caps, and ornamental work. The metal itself is very corrosion resistant but will develop a patina on the outer surface if it is exposed to outdoor elements, which will act as a barrier to the metal directly beneath it. This patina can occur naturally or be induced by chemicals, and can range in many different colors, with brown being the most common. It is very easy to bend and form, and can be soldered with ease.

Note:
-Standard mill finish.
-Has no protective film.  May have minor scratching.

Soft copper coil has many of the same properties as cold rolled copper, but is much softer and malleable and recommended for ornamental work only.

Copper expanded metal comes from 0.050" thick copper sheet that is expanded. We stock copper expanded metal in 300 to 500 foot coils. Copper expanded metal is thin enough to be rolled by hand and pieces measuring over 4' in length will typically be rolled up for shipping purposes.

With our copper expanded metal the long way of the diamond runs along the width. We can typically cut pieces that are 10' or shorter to size along the width, but you will need to call a sales representative at 877-484-0088 to discuss that option.

The copper expanded metal openings measure as follows:

3/4" Mesh
Short way of diamond opening = ~ 3/4"
Long of diamond opening = ~ 1 3/4"

5/8" Mesh
Short way of diamond opening = ~ 1/2"
Long of diamond opening = ~1 1/8"

Copper expanded metal is typically used for chimney caps, animal guards, and other projects that are decorative, where conductivity is needed, or that requires a long lasting, anti-corrosive metal. Copper expanded metal would not be recommended for uses in grills, trailers, catwalks etc. since it isn't strong enough for those applications.

Copper expanded metal is very corrosion resistant but will develop a patina on the outer surface if it is exposed to outdoor elements, which will act as a barrier to the metal directly beneath it. The patina on copper expanded metal can occur naturally or be induced by chemicals, and can range in many different colors, with brown being the most common. Copper expanded metal is very easy to bend and solder.

These trim moldings are made from the same 16 ounce copper that we sell in sheet form. They are used to attach sheets as wall coverings and backsplashes, along with providing aesthetic covering for seams between sheets and around corners. Our trim moldings have deep pockets to allow for variance in the existing wall and also have extra wide nailing strips to make installation more convenient.

Note: -When ordering material, you will need to subtract from the sheet size to account for the trim (see drawings).
-Trim molding can be attached to the wall with screws, nails, or adhesive prior to installing the sheets.

Choose from six types of copper diamond quilt patterns. With the availability of square or elongated diamonds and from small to large, we have the diversity to fit your project. As with our other embossed designs, we make these based on a 4" x 4" up to 24" x 24" repeating patterns.

This material is commonly used for architectural applications such as kitchen backsplashes and wall coverings.

When using full sheets and using our trim molding to connect the sheets, our modular design will allow the patterns on connecting sheets to line up perfectly.

CPD3 - The smaller-size choice of the square diamonds, these diamonds measure 3" from point to point.

CPD4 - An improvement to the common quilted pattern, our design is based on a 2.82" side to side dimension instead of the common 3". This causes the point to point dimension to be an even 4", allowing the diamonds to be full on all edges of a full 4' x 10' or 4' x 8' sheet. The common 3" design will not line up on full sheets and not give a seamless transition to full sheets installed next to each other.

CPD6 - The mid-size choice of the square diamonds, these diamonds measure 6" from point to point.

CPD12 - The larger choice of the square diamonds at 12" x 12" from point to point.

CPDT63 - For a tighter pattern, these elongated diamonds measure 3" x 6" from point to point.

CPDT84 - The taller choice of the elongated diamonds, these measure 4" x 8" from point to point.

Note: Embossed Diamond textured finish comes with a removable protective film.

Choose from three types of copper basket weave patterns. Ranging from a basic design to an intricate appearing classic basket weave, these pieces are all modular and based on a 12" x 12" repeating pattern.

This material is commonly used for architectural applications such as kitchen backsplashes and wall coverings.

When using full sheets and using our trim molding to connect the sheets, our modular design will allow the patterns on connecting sheets to line up perfectly.

CPBW1 - This copper basket weave based on a brick patio design uses 3" x 6" rectangles that repeat nicely on a 12" square.

CPBW2 - A variation of the brick patio basket weave, the offset pattern creates a more intricate look while still using the 3" x 6" rectangles.

CPBW3 - This classic basket weave pattern has a deceptively simple pattern that creates the full appearance of an intricate basket weave. Using 4" x 8" rectangles, this pattern can still be repeated on a 12" square.

Note: Basket Weave textured finish comes with a removable protective film.

The herringbone pattern, commonly used for floor and wall tiling, along with brick patterns, can now be purchased in copper for your own decorative use.

This material is commonly used for architectural applications such as kitchen backsplashes and wall coverings.

When using full sheets and using our trim molding to connect the sheets, our modular design will allow the patterns on connecting sheets to line up perfectly.

CPHPB - Using 3" x 6" rectangles, this pattern can be cut to a variety of sizes and still have the classic look of the herringbone design.

Note: Embossed Herringbone textured finish comes with a removable protective film.

The hopscotch pattern, originally known as Pythagorean tiling, combines squares of two sizes in to an intricate pattern that has been commonly used on floors and floor tiles.

This material is commonly used for architectural applications such as kitchen backsplashes and wall coverings.

When using full sheets and using our trim molding to connect the sheets, our modular design will allow the patterns on connecting sheets to line up perfectly.

CPHPS - Using 3" and 6" squares, the hopscotch pattern brings an interesting and attractive design on to the copper sheet.

Note: Embossed Diamond textured finish comes with a removable protective film.

The Diamond and Square embossed pattern provides another simple, yet appealing design to be used for many home and commercial projects.

This material is commonly used for architectural applications such as kitchen backsplashes and wall coverings.

When using full sheets and using our trim molding to connect the sheets, our modular design will allow the patterns on connecting sheets to line up perfectly.

CPDS - Utilizing 6" x 6" squares, four pieces are laid together with a 4.24" diamond in the center. This creates a modular design based on a 12" x 12" pattern that can be repeated up to our full 48" x 120" sheets.

Note: Embossed Diamond & Squares textured finish comes with a removable protective film.

The square grid pattern is one of most basic patterns, but comes with the versatility to be cut to many sizes and not worrying about patterns being aligned or matching with other sheets.

This material is commonly used for architectural applications such as kitchen backsplashes and wall coverings.

When using full sheets and using our trim molding to connect the sheets, our modular design will allow the patterns on connecting sheets to line up perfectly.

CPSG4 - The grid uses 4" x 4" squares embossed on to .027 gauge copper sheet.

Note: Embossed Square Grid textured finish comes with a removable protective film.

Named after the pattern originally used in the New York subway system in the early 1900's, this design has been commonly used in kitchens and bathrooms for decades.

This material is commonly used for architectural applications such as kitchen backsplashes and wall coverings.

When using full sheets and using our trim molding to connect the sheets, our modular design will allow the patterns on connecting sheets to line up perfectly.

CPSBW - Our design uses 3" x 6" rectangles to create the classic look on copper sheets. You can bring the New York subway to your own home!

Note: Embossed Subway textured finish comes with a removable protective film.

Our stainless countertops are made from prime 16 gauge 304 18/8 stainless steel.

Our copper countertops are made from prime 48 ounce (16G, .064") copper sheet.

We manufacture all of our countertops and sinks in a modern manufacturing facility located in NC.

From sales to fabrication, from engineering to shipping - through and through, we have what it takes to get the job done quickly with precision and efficiency.

Under-mount Sink

We design and build our sinks in house using machinery and old fashioned craftsmanship. Each sink is made to order regardless of size.

Design features

• .75" flange is located on all sides
• 304 Stainless Steel or 48oz (16G, .064") Copper
• Brushed Finish
• 5/8" Radius Corners
• Functional Drain Grooves
• Center, Rear Drain Placement
• 3 1/2" Drain Opening

Our stainless countertops are made from prime 16 gauge 304 18/8 stainless steel.

Our copper countertops are made from prime 48 ounce (16G, .064") copper sheet.

We manufacture all of our countertops and sinks in a modern manufacturing facility located in NC.

From sales to fabrication, from engineering to shipping through and through, we have what it takes to get the job done quickly with precision and efficiency.

Drop-in Sink

We design and build our sinks in house using machinery and old fashioned craftsmanship. Each sink is made to order regardless of size.

Design features

• .75" flange is located on all sides
• 304 Stainless Steel or 48oz (16G, .064") Copper
• Brushed Finish
• 5/8" Radius Corners
• Functional Drain Grooves
• Center, Rear Drain Placement
• 3 1/2" Drain Opening

The Flat countertop features include:

• Standard square edge on (3) sides
• Equalizer edge on back side

Equalizer Edge - backer is positioned 3/8" from rear edge of material, leaving 3/8" of stainless sheet for easy wall penetration to help compensate for uneven wall surfaces.

Our stainless steel stock countertops are made from prime 16 gauge 304 18/8 stainless steel.

Our copper countertops are made from prime 48 ounce (16G, .064") copper sheet.

Additional Features:

• Choice of moisture resistant MDF wood backer or stainless channel backer
• Mounting brackets included
• Equalizer Edge (on flat & backsplash model)
• Standard 25" depth
• Brushed Satin Finish
• 1/8" radius square edges

Need a sink? You have the ability to select a stock sink or design your own.

The Island countertop features include:

• Standard square edge on all (4) sides

Our stainless steel stock countertops are made from prime 16 gauge 304 18/8 stainless steel.

Our copper countertops are made from prime 48 ounce (16G, .064") copper sheet.

Additional Features:

• Choice of moisture resistant MDF wood backer or stainless channel backer
• Mounting brackets included
• Equalizer Edge (on flat & backsplash model)
• Standard 25" depth
• Brushed Satin Finish
• 1/8" radius square edges

Need a sink? You have the ability to select a stock sink or design your own.

The 5" Backsplash countertop features include:

• Standard square edge on (3) sides
• Seamlessly integrated 5" backsplash
• Backsplash has no backer for Equalizer Edge functionality

Equalizer Edge - backer is positioned 3/8" from rear edge of material, leaving 3/8" of stainless sheet for easy wall penetration to help compensate for uneven wall surfaces.

Our stainless steel stock countertops are made from prime 16 gauge 304 18/8 stainless steel.

Our copper countertops are made from prime 48 ounce (16G, .064") copper sheet.

Additional Features:

• Choice of moisture resistant MDF wood backer or stainless channel backer
• Mounting brackets included
• Equalizer Edge (on flat & backsplash model)
• Standard 25" depth
• Brushed Satin Finish
• 1/8" radius square edges

Need a sink? You have the ability to select a stock sink or design your own.

Stainless Supply offers a broad selection of metal corner guards that are sure to suit your needs. Adding a stylish form of protection to your new or existing walls has never been easier. Our corner guards are offered with or without pre-drilled holes that make your installation simple and easy. If you choose not to have mounting holes Stainless Supply provides you the option of having double-sided heavy-duty adhesive strips already applied to your corner guards for quick installation.

• Stylish Protection
• Drilled or undrilled mounting options
• Rounded corners
• Easy installation
• Made in the USA

All corner guards come in clear bags. We care about quality, so we inspect, peel and clean each one before bagging them.